|
Size: 1075
Comment:
|
← Revision 12 as of 2013-07-12 18:18:09 ⇥
Size: 1943
Comment: converted to 1.6 markup
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| ||<:30%>[:PiraScheme#WavesSound: Table of Waves and Sound Demonstration]||<:30%>[:WSEquipmentList: List of Waves and Sound Equipment & Supplies]||<:30%>[:Demonstrations:Lecture Demonstrations]|| | ||<:30%>[[PiraScheme#WavesSound| Table of Waves and Sound Demonstration]]||<:30%>[[WSEquipmentList| List of Waves and Sound Equipment & Supplies]]||<:30%>[[Demonstrations|Lecture Demonstrations]]|| |
| Line 5: | Line 5: |
| = Table DMM & Timer, 3A.EQ.100 = | = Table DMM & Timer, 3A.EQ105 = |
| Line 9: | Line 9: |
| * '''Cabinet:''' [:WavesSoundCabinet#WavesSoundLt:Waves and Sound (WS)] * '''Bay:''' [:WSCabinetLtBayB2: B2] |
* '''Cabinet:''' [[WavesSoundCabinet#WavesSoundLt|Waves and Sound (WS)]] * '''Bay:''' [[WSCabinetLtBayB2| B2]] |
| Line 13: | Line 13: |
| attachment:BenchMeterInterface01-400.jpg | {{attachment:BenchMeterInterface01-400.jpg}} |
| Line 21: | Line 21: |
| * Device is unable to measure | * N/A |
| Line 25: | Line 25: |
| 1. | 1. Plug in the blue Tyco chip in the back to show a decimal place. Moving the resistor on the card will move decimal place location. 1. Plug the 9 pin flat wire from the back to the DMM to the leg of one of the display table that contain an 8 digit external display. 1. Connect input to either channel A or B or both can be used if there are two inputs. There is a toggle switch for switching between the channels. 1. Select desired measurement type: frequency counter, timer, resistance, current, or voltage by pressing corresponding button. 1. Select desired scaling by pressing corresponding button (not applicable to frequency or current): 2 kΩ to 20 kΩ, 2 mA to 2 A, and 20 V to 2000 V. 1. If using the timer option, there is a start/stop and a reset button on the front of the unit. The Cat5 switch also performs these functions. |
| Line 29: | Line 34: |
| * | * N/A |
| Line 32: | Line 37: |
| ||attachment:BenchMeter01-250.jpg||attachment:BenchMeter04-250.jpg||attachment:BenchMeterInterface03-250.jpg|| ||attachment:Cat5Switch-250.jpg||attachment:Components01-zoom-250.jpg||attachment:attachment:Components02-250.jpg|| ||attachment:Components03-250.jpg||attachment:Components04-250.jpg||attachment:Components05-250.jpg|| |
||{{attachment:BenchMeter01-250.jpg}}||{{attachment:BenchMeter04-250.jpg}}||{{attachment:BenchMeterInterface03-250.jpg}}|| ||{{attachment:Cat5Switch-250.jpg}}||{{attachment:Components01-zoom-250.jpg}}||{{attachment:attachment:Components02-250.jpg}}|| ||{{attachment:Components03-250.jpg}}||{{attachment:Components04-250.jpg}}||{{attachment:Components05-250.jpg}}|| |
| Line 37: | Line 42: |
| [:Instructional:Home] | [[Instructional|Home]] |
Table DMM & Timer, 3A.EQ105
Location:
Cabinet: Waves and Sound (WS)
Bay: B2
Shelf: 2
Description:
This is a homemade multimeter.
Important Notes:
- N/A
Setup:
- Plug in the blue Tyco chip in the back to show a decimal place. Moving the resistor on the card will move decimal place location.
- Plug the 9 pin flat wire from the back to the DMM to the leg of one of the display table that contain an 8 digit external display.
- Connect input to either channel A or B or both can be used if there are two inputs. There is a toggle switch for switching between the channels.
- Select desired measurement type: frequency counter, timer, resistance, current, or voltage by pressing corresponding button.
- Select desired scaling by pressing corresponding button (not applicable to frequency or current): 2 kΩ to 20 kΩ, 2 mA to 2 A, and 20 V to 2000 V.
- If using the timer option, there is a start/stop and a reset button on the front of the unit. The Cat5 switch also performs these functions.
Cautions, Warnings, or Safety Concerns:
- N/A
|
|
|
|
|
|
|
|
|
