|
Size: 1626
Comment:
|
Size: 1661
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| ## page was renamed from M-12b-200 | |
| Line 5: | Line 6: |
| ==== Quantity: 14 ==== | |
| Line 7: | Line 9: |
| * Lab Table Setup | |
| Line 8: | Line 11: |
| [[attachment:M-12b-200.png|{{attachment:M-12b-200.png|attachment:M-12b-200.png|width="500 height=185"}}]] | |
| Line 9: | Line 13: |
| <<Thumbnail(M-12b-200.png,500,200)>> | |
| Line 12: | Line 15: |
| * 1 [[4327-1#PASCO_Hooke.27s_Law_Unit|Hooke's Law Unit]] | |
| Line 17: | Line 21: |
| * 1 [[Miscellaneous#Glider_with_Timing_Plate|Glider w/ Timing Plate]] * w/ [[Miscellaneous#Reflecting_Vane|Reflecting Vane]] * 1 [[Miscellaneous#Glider_Accessory_Kit|Glider Accessory Kit]] * 1 [[4327-2#PASCO_Motion_Sensor|PASCO Motion Sensor]] * w/ [[4327-2#PASCO_Motion_Sensor_Cord|Cable]] * w/ [[4327-1#S-W_T-Base_1.2BAC8-2.22_Support_Stand|1/2" T-Stand]] * w/ [[4327-2#Thorlabs_Right-Angle_Clamp|Right Angle Clamp]] * w/ [[4327-2#Small_.281.2BAC8-4.22.29_Stainless_Steel_Rod|1/4" L-Rod]] |
* 1 [[Air Track Cart#Glider_with_Timing_Plate|Glider w/ Timing Plate]] * w/ [[Air Track Cart#Reflecting_Vane|Reflecting Vane]] * 1 [[Air Track Cart#Glider_Accessory_Kit|Glider Accessory Kit]] * 1 Motion Sensor * w/ Cable * w/ [[4327-1#S-W_T-Base_1.2BAC8-4.22_Support_Stand|1/4" T-Stand]] |
| Line 26: | Line 29: |
| * w/ [[4327-2#PASCO_Photogate_Cord|Cord]] If Not Attached | * w/ [[4327-3#PASCO_Photogate_Cord|Cord]] |
| Line 28: | Line 31: |
| ===== Also ===== * 2 [[4327-1#PASCO_Hooke.27s_Law_Unit|Hooke's Law Units]] |
===== Also for Classroom ===== |
| Line 32: | Line 35: |
| Line 33: | Line 37: |
| * Position adjustable stop at mid-point * Attach springs toglider, stop and end-points |
|
| Line 38: | Line 45: |
| Line 39: | Line 47: |
| [[200 Level Index]] [[M-12-200 | M-12]] |
[[200 Level Index]] [[M-12-200|M-12]] |
M-12b: Air Track Resonance & Simple Harmonic Motion
Quantity: 14
- Lab Table Setup
Experiment Contents
1 PC & Interface
w/ Air Supply
w/ Hose-T
w/ Hose
- w/ Adjustable Stop
- 1 Motion Sensor
- w/ Cable
w/ 1/4" T-Stand
w/ Cord
w/ 1/4" T-Stand
Also for Classroom
4 Boxes 25mm Springs
- 1 Weight Box w/50g Weight Hangers (In Lab)
Check
- Position adjustable stop at mid-point
- Attach springs toglider, stop and end-points
- Computer Set-Up (PC, Interface On Before Computer, Sensors Work)
- Air Tracks Work (Clean, No Clogged Air Holes, Glider Movement)
- Glider Accessory Kit Including Glider Bands
- Hose Intact
- Always Run 2 Tracks From Same Air Supply