Differences between revisions 7 and 29 (spanning 22 versions)
⇤ ← Revision 7 as of 2011-07-21 18:07:28 →
Size: 1461
Editor: ryan
Comment:
← Revision 29 as of 2018-06-12 19:17:43 → ⇥
Size: 1868
Editor: PriyaPathare
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
## page was renamed from M-12b-200
Line 5: Line 6:
==== Quantity: 14 ====
Line 7: Line 9:
 * Lab Table Setup
Line 8: Line 11:
[[attachment:M-12b-200.png|{{attachment:M-12b-200.png|attachment:M-12b-200.png|width="500 height=185"}}]]
Line 9: Line 13:
{{attachment:M-12b-200.png|M-12b|width=500}}
Line 12: Line 15:
 * 1 Air Track
  * w/Air Supply
  * w/Hose-T
  * w/Hose
  * w/Adjustable Stop
 * 1 [[Miscellaneous#Glider_with_Timing_Plate|Glider w/ Timing Plate]]
  * w/ [[Miscellaneous#Reflecting_Vane|Reflecting Vane]]
 * 1 [[Miscellaneous#Glider_Accessory_Kit|Glider Accessory Kit]]
 * 1 [[4327-2#PASCO_Motion_Sensor|PASCO Motion Sensor]]
  * w/ [[4327-2#PASCO_Motion_Sensor_Cord|Cable]]
  * w/ [[4327-1#S-W_T-Base_1.2BAC8-2.22_Support_Stand|1/2" T-Stand]]
  * w/ [[4327-2#Thorlabs_Right-Angle_Clamp|Right Angle Clamp]]
  * w/ 1/4" L-Rod		  * 1 [[4327-1#PASCO_Hooke.27s_Law_Unit|Hooke's Law Unit]]
 * 1 [[Air Track Cart#Air_Track|Air Track]]
  * w/ [[Air Track Cart#Air_Supply|Air Supply]]
  * w/ [[Air Track Cart#T-Hose|Hose-T]]
  * w/ [[Air Track Cart#Air_Hose|Hose]]
  * w/ Adjustable Stop
 * 1 [[Air Track Cart#Glider_with_Timing_Plate|Glider w/ Timing Plate]]
  * w/ [[Air Track Cart#Reflecting_Vane|Reflecting Vane]]
 * 1 [[Air Track Cart#Glider_Accessory_Kit|Glider Accessory Kit]]
 * 1 [[4327-2#PASCO_Motion_Sensor|Motion Sensor]]
  * w/ Cable
  * w/ [[4327-1#S-W_T-Base_1.2BAC8-4.22_Support_Stand|1/4" T-Stand]]
Line 26: Line 29:
  * w/ [[4327-2#PASCO_Photogate_Cord|Cord]] If Not Attached   * w/ [[4327-3#PASCO_Photogate_Cord|Cord]]
Line 28: Line 31:
===== Also =====
 * 2 [[4327-1#PASCO_Hooke.27s_Law_Unit|Hooke's Law Units]]
==== Also for Classroom ====
Line 32: Line 35:
Line 33: Line 37:
 * For pairs of tables, air supplies should be on chairs between the tables. Run two tracks from one supply via a Hose-T.
 * For tables against a wall, air supplies should be on the table next to the Pasco interfaces.

 * Position adjustable stop at mid-point
 * Attach springs toglider, stop and end-points
Line 37: Line 47:
 * Always Run 2 Tracks From Same Air Supply
Line 39: Line 49:
[[200 Level Index]]
[[M-12-200 | M-12]]		 [[200 Level Index]] [[M-12-200|M-12]]

M-12b: Air Track Resonance & Simple Harmonic Motion

Quantity: 14

Contents

  1. M-12b: Air Track Resonance & Simple Harmonic Motion
    1. Quantity: 14
    2. Experiment Contents
    3. Also for Classroom
    4. Check

  • Lab Table Setup

attachment:M-12b-200.png

Experiment Contents

Also for Classroom

  • 4 Boxes 25mm Springs

  • 1 Weight Box w/50g Weight Hangers (In Lab)

Check

  • For pairs of tables, air supplies should be on chairs between the tables. Run two tracks from one supply via a Hose-T.
  • For tables against a wall, air supplies should be on the table next to the Pasco interfaces.
  • Position adjustable stop at mid-point
  • Attach springs toglider, stop and end-points
  • Computer Set-Up (PC, Interface On Before Computer, Sensors Work)
  • Air Tracks Work (Clean, No Clogged Air Holes, Glider Movement)
  • Glider Accessory Kit Including Glider Bands
  • Hose Intact

200 Level Index M-12

il: M-212b (last edited 2018-06-12 19:17:43 by PriyaPathare)