Differences between revisions 1 and 6 (spanning 5 versions)
⇤ ← Revision 1 as of 2011-06-07 15:14:08 →
Size: 1157
Editor: ryan
Comment:
← Revision 6 as of 2018-01-05 15:14:17 → ⇥
Size: 1691
Editor: BrettUnks
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
## page was renamed from H-4-200
Line 5: Line 6:
==== Quantity: 6 ====
Line 9: Line 11:
 * 1 Heat Engine Assembly (w/ Cylinder and Piston)
 * 1 Aluminum Air Chamber (O1.5" OD X 3.6" H)
 * 2 #8 Rubber Stoppers (1-Hole and 2-Hole)
 * 3 Clear Tubing Configurations		  * 1 [[4325-1#Heat_Engine_Cylinder_and_Piston|Heat Engine Assembly (w/ Cylinder and Piston)]]
 * 1 [[4325-1#Aluminum_Air_Chamber|Aluminum Air Chamber (O1.5" OD X 3.6" H)]]
 * 2 [[4325-1#Rubber_Stopper|#8 Rubber Stoppers (1-Hole and 2-Hole)]]
 * 3 [[4325-1#Clear_Tubing_Configuration|Clear Tubing Configurations]]
Line 16: Line 18:
 * 1 Universal Table Clamp and 1/2" Support Rod
 * 1 1,000mL Plastic Beaker
 * PASCO Steam Generator
 * 1 Fluke Digital Thermometer and Probe
 *1 PASCO Bracket Mounted Pressure Sensor
  *w/ 1/4" T-Stand		  * 1 [[4327-2#Universal_Table_Clamp|Universal Table Clamp]]
  * w/ [[4327-2#Large_.281.2BAC8-2.22.29_Stainless_Steel_Rod|1/2" Support Rod]]
 * 1 [[4325-3#A1000mL_Plastic_Beaker|1,000mL Plastic Beaker]]
 * [[4325-1#PASCO_Steam_Generator|PASCO Steam Generator]]
 * 1 [[4325-3#Fluke_Digital_Thermometer|Fluke Digital Thermometer]]
  * w/ [[4325-3#Temperature_Probe|Probe]]
 *1 [[4325-3#PASCO_Pressure_Sensor|PASCO Bracket Mounted Pressure Sensor]]
  * w/ [[4327-1#S-W_T-Base_1.2BAC8-4.22_Support_Stand|1/4" T-Stand]]
Line 24: Line 28:
 * 1 Ice Bucket w/ Cover  * 1 [[4325-2#Ice_Bucket|Ice Bucket w/ Cover]]
Line 38: Line 42:
[[Level Index]] [[200 Level Index]]

H-4: Heat Engine

Quantity: 6

Contents

  1. H-4: Heat Engine
    1. Quantity: 6
    2. Experiment Contents
    3. Check
  2. Caution

Experiment Contents

Also

Check

  • Computer Set-Up (PC, Interface On Before Computer, Sensors Work)
  • Ice Chest Filled (In 4329)
  • Extra Paper Towels

Caution

  • Do Not Immerse Heat Engine Assembly in Liquid
  • Use Only Non-Caustic / Non-Toxic Gases (Air, Helium)
  • Release Tubing Clamps After Use (To Avoid Deforming Tubing)
  • Maximum Pressure: 345 kPA
  • Do Not Lubricate Piston Or Cylinder

200 Level Index

il: H-204 (last edited 2018-01-05 15:14:17 by BrettUnks)