|
Size: 1823
Comment:
|
← Revision 29 as of 2018-06-04 18:51:12 ⇥
Size: 1833
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| ## page was renamed from E-6-200 | |
| Line 4: | Line 5: |
| === E-6: Cathode Ray Oscilloscope And Differential Amplifier === | === E-6: Oscilloscopes and RC Decay === |
| Line 8: | Line 9: |
| [[attachment:E-6-200.png|{{attachment:E-6-200.png|attachment:E-6-200.png|width="500 height=138"}}]] | [[attachment:E-6-200.png|{{attachment:E-6-200.jpg|attachment:E-6-200.jpg|width="500 height=138"}}]] |
| Line 12: | Line 13: |
| * w/ 2 [[Hanging Oscilloscope Probes#BNC to Alligator Cables|Oscilloscope Probes]] * 1 [[3323-1#Kruhn-Hite_Function_Generators|Function Generator]] |
* w/ 2 [[Hanging Oscilloscope Probes#BNC_to_Alligator_Cables|Oscilloscope Probes]] * 1 Oscilloscope Manual * 1 [[3323-1#Kruhn-Hite_Function_Generators|Function Generator]] |
| Line 16: | Line 18: |
| * 1 [[3323-3#BNC to Alligator Cables|BNC to Alligator Cable]] | * 2 [[3323-3#BNC_to_Alligator_Cables|BNC to Alligator Cable]] |
| Line 20: | Line 22: |
| ===== Also ===== * 1 Oscilloscope Manual |
|
| Line 25: | Line 24: |
| * Resistor Set (1kΩ, 2.2kΩ, 3.3kΩ, 4.7kΩ, 10kΩ, 20kΩ, 100kΩ, 10MΩ) | * Resistor Set (100Ω, 200Ω, 400Ω, 1kΩ, 2.2kΩ, 3.3kΩ, 4.7kΩ, 10kΩ, 20kΩ, 100kΩ, 10MΩ) |
E-6: Oscilloscopes and RC Decay
Quantity: 39
Experiment Contents
w/ 2 Oscilloscope Probes
- 1 Oscilloscope Manual
w/Kit
Check
Plug Board Kit (30 Items)
- Resistor Set (100Ω, 200Ω, 400Ω, 1kΩ, 2.2kΩ, 3.3kΩ, 4.7kΩ, 10kΩ, 20kΩ, 100kΩ, 10MΩ)
- 8 Bridge Plugs
- Capacitor Set (47nF, 1μF, 0.47μF)
- Diode
- Inductor (1 H)
- SPDT Switch
- Variable Resistor (1k)
- Transistor (2N1480)
- Differential Amplifier
- Adapter Set (2 Pomona 1269, 2 Pomona 1296, 1 BNC 'T')
Troubleshooting
If the output of the differential amplifier is unstable, verify that all E-6 equipment is plugged into the Tripp Lite power strip, which is located adjacent to the lab table (see photo below), and the Tripp Lite power strip is plugged into the wall. No E-6 equipment should be plugged into the power strip on the back of the computer cart, which has a dubious ground (as of 3/10/14).
