maybe 3 nodes double node long tube bubbles 'dripping'

I discovered an unusual bubble structure which is unexpectedly very stable. To make it, you blow a hemispherical bubble in a pan of soap water using a straw. Then, while still blowing through the straw, withdraw the straw from the bubble. Under the right conditions, a corrugated tube of soap film will form between the straw and the bubble. The tube collapses when you stop blowing. It can be proved that long cylindrical bubbles are unstable without airflow. As far as I know, nobody has studied bubble stability with airflow. It might be possible to publish a short article about this topic.

Proposal: Here bubble_proposal.pdf is the proposal that Sean & Lucas sent to Brett & Duncan, requesting equipment for this project.

Observations so far:

Blowing the bubbles by hand: In order to make the longest tubes, it's necessary to have a large flow rate, enough to cause audible & visible turbulence inside the tube. It is clear that these tubes are robustly stable, since they can oscillate enough during the turbulent phase to produce sound, without breaking! I think I saw transient states with up to 4 nodes or more. When I reduced the airflow after forming the tube, the number of nodes was reduced, and the turbulence went away. This is how I captured the picture with the distinct 2-node structure.

Blowing the bubbles with the comressed air supply: We used much larger tubes, 3/8" to 1/2" ID, compared to the straws I was using initially. It seemed to be harder to get more than 3 nodes (two anti-nodes), until we increased the concentration of detergent, added glycerine, and used distilled water. We also found that using a metal tube for the nozzle is much better than just blowing the bubbles with the end of a hose (which is curved, and the end is cut at an angle). Finally, tuning the airflow is critical. If the flow is too fast, the airflow is turbulent and this bursts the bubble. At low flow rate, trying to draw out the tube in order to produce more antinodes resulted in oscillations, and the bubble would eventually snap before we could reach the next antinode. With the proper flow rate, it appears to be possible to create tubes of arbitrary length.

Examining the videos shows that the first antinode decreases in diameter when the nozzle is being pulled out to create the longest bubbles. With low flow rate, moving the nozzle slowly closer & farther away causes the first antinode to vanish and re-form with the same shape. It may be important to pull the nozzle away quickly to induce a transition of some kind. Reducing the airflow causes antinodes to have larger diameter (can be much larger than the nozzle), while increased airflow causes the corrugations to flatten, resulting in a tube the same diameter as the nozzle. Reducing the flow also tends to reduce the number of antinodes, indicating that the wavelength of the structure is changing.

A common feature is the tight neck where the tube enters the base bubble. It would be interesting to see if the diameter of this neck changed with airflow rate. It appears to always be as small or smaller than the straw. At high airflow, it is not much, if any, smaller than the rest of the bubble tube.

It is possible to blow at a tangential angle without popping the bubble; in fact, the bubble tube can execute a 90-degree turn! With a bit of luck, you can also produce a stream that breaks up into bubble 'drops,' just like water streams do.

Pictures & Videos

videos of bubble blowing

http://www.youtube.com/watch?v=aE_zHbpF3Bo

single node more ambiguous structure

double node again maybe 3 nodes

Experimental equipment & techniques:

Here's what we have for equipment:

*A baking sheet for holding the bubble solution

*Dish detergent, glycerine & distilled water

*Some Tygon tubing attatched to the building air supply

*A single steel tube (ID 4.1mm)

*Digital camera (personal)

*Free image processing software (ImageJ)

Things we could measure:

*Surface tension

*Air flow (liters/second)

*Air flow stream lines (using fog/smoke)

*Pressure inside the straw, or the large bubble at the end

*Air speed within the bubble (tricky!)

We may be able to measure airflow with a venturi tube and surface tension using bubble pressure This would could be done with a single pressure sensor which is sensitive to very small pressure differences (0.5 <-> 50 Pa). We are looking into constructing or purchasing such a pressure sensor.

Pressure sensor:

Peizoelectric sensor, while extremely sensitive, are only effective for measuring pressure fluctuations and not static pressures, due to charge leakage. A better method seems to be measuring the deflection of a thin membrane exposed to a pressure difference. This can be done using capacitance or optically, among many other ways.

Optical method: http://link.aip.org/link/doi/10.1063/1.1143989 -- this may be the easiest. it looks very simple.

More complicated optical method: http://dx.doi.org/10.1364/OL.8.000286 -- has the advantage of compensating for changes in source intensity.

Capacitive method with LC oscillator: http://www.sensata.com/download/ipt_tech-note_1.pdf -- all the capacitive readout methods look tricky

Surface tension measurement: We'd like to measure the surface tension in order to compare the surface pressure to the stagnation pressure of the flow.

Bubble pressure method seems simple and accurate: http://dx.doi.org/10.1119/1.3623414

Airflow measurement:

A venturi tube can tell us the airflow rate we are supplying to the bubble tube. This handy calculator shows the flow velocities we could measure with a given pressure range:

http://www.efunda.com/formulae/fluids/venturi_flowmeter.cfm#calc

Air flow visualization:

We could use a source of smoke or fog to trace the streamlines of air passing through the bubble. One way to create fog is using dry ice or liquid nitrogen, which is available in the department in large quantities. We could also use smoldering materials (incense, cigarrette), chemical reactions (ammonia and hydrogen chloride vapor form fine crystals in mid-air), or commerical fog devices which rely on vaporizing a water/glycol mixture.

Internal flow velocity measurements: eventually we will need a way to measure the flow profiles inside the bubble tube. PIV and LDV are probably the two best choices I've seen. These methods require a bit of work, and also a laser. PIV is nice because it gives a 2-D profile and it goes along well with the goal of measuring the tube dimensions.

Particle image velocimetry: http://tejas.serc.iisc.ernet.in/currsci/jul102000/review%20article.pdf

Laser Doppler velocitimetry: http://link.aip.org/link/doi/10.1119/1.18051?ver=pdfcov

Surface flow measurement:

If there is recirculation (ie, a vortex) in the bulge, then there will be a stagnation point where the air flows along the surface toward the point from both sides. If the airflow causes the water in the film to flow due to drag at the surface, then the water will accumulate at the stagnation point. We could try putting very small particles in the soap solution to see if they accumulate at a stagnation point.

Adding rotation:

Mark Nornberg suggested placing blades with different pitches inside the blowing tube, to induce airflow rotation around the axis of the tube. This could add centrifugal force to the flow, possibly changing the stability or the amplitude of the corrugations.

Theory:

Equilibrium: the bubbles appear to be surfaces of roughly-constant 'mean curvature.' This means that the pressure inside the bubbles is also approximately constant along the length, according to the Young-Laplace law and force balance. (This is somewhat puzzling, since Bernoulli's law dictates that the pressure must be lower in the throats, if the flow velocity is higher there.) The pressure in the tube must be higher than in the terminating hemispherical bubble, since the larger bubble has lower curvature. This means that there is some pressure drop across the narrow neck where the tube joins the large bubble. It should be possible to create a long bubble tube with no corrugations if the downstream pressure could be increased, so that the narrow neck was unnecessary. There is also evidently very little pressure drop along the cylindrical part of the tube, so an arbitrarily long tube might be possible. It might also be possible to create a very long corrugated tube by lowering the flow rate of a pre-existing cylindrical tube; however, it may be that pressure loss is incurred at every neck, limiting the length of the tube. It is not clear why the flow rate controls the aspect ratio of the corrugations.

Stability: the constant-mean-curvature surfaces (unduloids) are not stable; they tend to 'neck off' into a string of spheres. That is to say, if the narrow part is pushed in a bit, it is no longer in equilibrium, and it continues to move inward until it collapses. If air is flowing through the neck, it must have a higher velocity as the throat decreases in radius, in order to keep the volumetric flow rate constant. But according to Bernoulli's principle, the pressure is lower where the velocity is higher. This implies that the pressure decreases in the neck, which would accelerate the inward motion of the walls! Clearly this is not the whole story. There may be vortexes in each bulge, which act to keep the column stable.

Relevant Articles:

Unduloid: a surface with constant mean curvature; they are solutions to the force balance for the case of constant pressure. They look alot like the bubble tubes we're blowing.

Wikipedia has a nice diagram: http://en.wikipedia.org/wiki/Unduloid

Mathematical formula for the unduloid is here: http://www.emis.de/journals/AM/07-5/mladenov.pdf

Description of stability of various forms including unduloids: http://www.math.ucla.edu/~bertozzi/papers/surfdiff98.pdf

Bubble Stability Without Flow: This is what happens without flow. These papers illustrate different techniques for solving the problem.

Analysis of Instability of a Cylindrical Soap Film of Finite Dimensions.http://dx.doi.org/10.1021/la970595k

Stability of interfaces of revolution with constant surface tension—the case of the catenoid. http://dx.doi.org/10.1016/0300-9467(70)85003-1

Stability and oscillations of a soap film: An analytic treatment. http://dx.doi.org/10.1119/1.12506

Good treatment of variational method for bubbles: http://farside.ph.utexas.edu/teaching/336l/fluidhtml/node51.html

Plateau-Rayleigh Instability: This is why a falling stream of water breaks into droplets. There is some similarity, but in our case the surface is not attached to the flow, and there is drag instead of acceleration due to gravity.

Wikipedia has a nice introduction: http://en.wikipedia.org/wiki/Plateau%E2%80%93Rayleigh_instability

On the breakup of viscous liquid thread. http://dx.doi.org/10.1063/1.868540

Nonlinear dynamics and breakup of free-surface flows. http://dx.doi.org/10.1103/RevModPhys.69.865

Lecture notes on surface tension, ch 5. web.mit.edu/1.63/www/Lec-notes/Surfacetension/Lecture5.pdf

Fluid flow in undulating tubes:

Navier - stokes equation http://en.wikipedia.org/wiki/Navier%E2%80%93Stokes_equations

Theory of vortexes in undulating tubes, with diagrams (Ralph): http://dx.doi.org/10.1115/1.3242656

Image of vortex in undulating tube!!! (Deiber & Schowalter) : http://dx.doi.org/10.1002/aic.690250410

Some theory about flow in undulating tubes, with diagrams of vortexes (Lahbabi & Chang): http://dx.doi.org/10.1016/0009-2509(86)80034-3

Theory of flow in an undulating tube (not so many pretty pictures) (Floryan): http://dx.doi.org/10.1017/S0022112003003987

External-flow-stabilization of long liquid columns

http://dx.doi.org/10.1016/0301-9322(94)90092-2

Add your name here if you'd like to become involved with the project:

* Lucas Morton

* Bai Yang Wang

* Duncan Carlsmith

Hey Lucas, here is a video of using a speaker to wiggle water. Maybe it will inspire. -duncan

http://www.creativeplanetnetwork.com/dv/news/watch-amazing-video-sound-waves-appearing-water/62003

More inspiration

Engineers explain physics of fluids over 100 years after original discovery,

http://www.rdmag.com/news/2013/03/engineers-explain-physics-fluids-over-100-years-after-original-discovery-0

Dripping honey explained

http://physics.aps.org/articles/v6/38, http://prl.aps.org/abstract/PRL/v110/i14/e144501

When a Jet Hits a Soap Film arxiv.org/1203.0842v2.pdf

None: Bubble Stability (last edited 2014-04-16 15:06:57 by Lucas Morton)